行業資訊
濟南壓路機租賃：機器磨合要點與高效使用技巧
來源：http://m.seatostar.com/ 日期：2025-07-08
濟南地區租賃的壓路機在投入正式作業前，充分的磨合處理，這是保障設備高效運行、延長使用壽命的關鍵環節。磨合過程需遵循科學規范，避免因操作不當導致部件磨損加劇，影響作業效果。
Before the roller leased in Jinan area is put into formal operation, it needs to undergo sufficient running in treatment, which is a key link to ensure the efficient operation of the equipment and extend its service life. The running in process should follow scientific standards to avoid exacerbating component wear and affecting operational effectiveness due to improper operation.
啟動階段的磨合需循序漸進。首次啟動壓路機后，應先怠速運轉 3-5 分鐘，讓發動機、液壓系統等關鍵部件逐步達到工作溫度，減少冷啟動時的機械磨損。待怠速穩定后，緩慢操作操縱桿，使壓路機在空載狀態下進行前后行駛、轉向等基礎動作，每個動作保持 5-10 秒，重復 3-5 次，讓傳動系統、制動系統初步適應運行節奏。此時需注意觀察設備有無異常聲響或漏油現象，若發現問題應立即停機檢查，排除故障后再繼續磨合。
The running in during the start-up phase needs to be gradual. After starting the roller for the first time, it should idle for 3-5 minutes to gradually reach the working temperature of key components such as the engine and hydraulic system, reducing mechanical wear during cold start. After the idle speed stabilizes, slowly operate the control lever to make the roller perform basic actions such as forward and backward driving, steering, etc. in an unloaded state. Each action should be maintained for 5-10 seconds and repeated 3-5 times to allow the transmission system and braking system to initially adapt to the operating rhythm. At this time, it is necessary to observe whether there are any abnormal sounds or oil leaks in the equipment. If any problems are found, the machine should be stopped immediately for inspection, and the fault should be eliminated before continuing to run in.
負載磨合需控制作業強度。經過空載磨合后，可進行低負載作業，濟南地區常見的初始負載建議控制在額定負載的 50%-60%。在壓實路面時，先選擇平整度較高的場地，以低速行駛（通常不超過 3 公里 / 小時）進行碾壓，單次碾壓距離不宜過長，保持在 50-100 米范圍內，往返作業 3-5 次后停機冷卻，讓齒輪箱、軸承等部件散熱。磨合期間避免急加速、急剎車，轉向時需提前減速，減少機械沖擊對傳動系統的損傷。
Load running in requires controlling the intensity of the operation. After no-load running in, low load operation can be carried out. It is recommended to control the initial load in Jinan area to 50% -60% of the rated load. When compacting the road surface, first choose a site with high flatness and drive at low speed (usually not exceeding 3 kilometers per hour) for rolling. The single rolling distance should not be too long and should be kept within the range of 50-100 meters. After 3-5 round trips, stop the machine to cool down and allow the gearbox, bearings, and other components to dissipate heat. During the running in period, avoid sudden acceleration and braking, and slow down in advance when turning to reduce mechanical impact damage to the transmission system.
液壓系統的磨合要注重壓力穩定。壓路機的液壓系統對磨合質量尤為敏感，操作時需保持液壓油壓力在正常范圍，避免頻繁切換高壓狀態。在升降碾壓輪、調整振幅等操作時，動作要平穩緩慢，讓液壓泵、油缸等部件在溫和工況下逐漸形成配合默契。每天作業結束后，需檢查液壓油液位和清潔度，若發現油液中有雜質或乳化現象，應及時更換，防止污染系統內部元件。
The running in of hydraulic systems should pay attention to pressure stability. The hydraulic system of a road roller is particularly sensitive to the quality of running in, and it is necessary to maintain the hydraulic oil pressure within the normal range during operation to avoid frequent switching of high-pressure states. When operating the lifting and rolling wheels, adjusting the amplitude, etc., the movements should be smooth and slow, allowing the hydraulic pump, oil cylinder and other components to gradually form a coordinated understanding under mild working conditions. After completing daily homework, it is necessary to check the hydraulic oil level and cleanliness. If impurities or emulsification are found in the oil, it should be replaced in a timely manner to prevent contamination of internal components of the system.
磨合期間的保養不可忽視。作業結束后，需對壓路機進行全面檢查：清理碾壓輪上的泥土、碎石等雜物，避免殘留硬物在下次作業時劃傷部件；檢查輪胎（或鋼輪）的胎壓和磨損情況，確保受力均勻；對各潤滑點加注潤滑油，重點關注傳動軸、軸承等易磨損部位。濟南地區多沙塵天氣，磨合期間還需加強空氣濾清器的清潔，防止灰塵進入發動機導致缸體磨損。
Maintenance during the break in period cannot be ignored. After the homework is completed, a comprehensive inspection of the roller should be carried out: clean the soil, gravel and other debris on the rolling wheel to avoid leaving hard objects that may scratch the components during the next operation; Check the tire pressure and wear of the tires (or steel wheels) to ensure even force distribution; Add lubricating oil to each lubrication point, with a focus on wear prone parts such as transmission shafts and bearings. In the dusty weather of Jinan area, it is necessary to strengthen the cleaning of the air filter during the running in period to prevent dust from entering the engine and causing cylinder wear.
磨合后的性能測試是高效使用的前提。經過 30-50 小時的磨合后，需對壓路機的作業性能進行測試：在標準壓實場地內，以不同速度和振幅進行碾壓試驗，觀察壓實效果是否均勻；檢查制動系統的響應速度和制動距離，確保符合安全標準；測試液壓系統在滿負載狀態下的穩定性，無滲漏、卡頓等現象方可投入正式作業。
Performance testing after running in is a prerequisite for efficient use. After 30-50 hours of running in, the operational performance of the roller needs to be tested: in a standard compaction site, rolling tests are conducted at different speeds and amplitudes to observe whether the compaction effect is uniform; Check the response speed and braking distance of the braking system to ensure compliance with safety standards; Test the stability of the hydraulic system under full load, and only when there is no leakage, jamming, or other phenomena can it be put into formal operation.
濟南壓路機租賃后的磨合過程，核心在于通過低負荷、平穩操作讓各部件形成良好配合，減少早期磨損。嚴格遵循磨合規范，結合日常細致保養，能使壓路機在后續作業中保持高效性能，適應道路修建、場地平整等多種工程需求。
The core of the running in process of Jinan roller after leasing is to form a good fit between various components through low load and smooth operation, reducing early wear and tear. Strictly following the running in specifications, combined with daily meticulous maintenance, can enable the roller to maintain efficient performance in subsequent operations, adapt to various engineering needs such as road construction and site leveling.
本文由濟南壓路機租賃友情奉獻.更多有關的知識請點擊:http://m.seatostar.com真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.
This article is a friendly contribution from Jinan Water Stable Mixing Plant For more information, please click: http://m.seatostar.com Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.
公司地址：濟南市商河縣賈莊鎮民營經濟創業園
公司名稱:永誠廣建公路材料（山東）有限公司 
備案號：